Complete Directory

Estimate steel weight for plate/sheet and common bar shapes using dimensions, density, quantity, and scrap allowance.

• Steel
• Weight
• Density

Estimate furnace size (output and input BTU/h) from heated area, ceiling height, insulation level, climate, and AFUE.

• BTU/h
• AFUE
• Heat load

Estimate weld metal weight, volume, and required filler material based on process efficiency (MIG, Stick, TIG).

• Fabrication
• Filler
• Consumables

Check GD&T true position for anchor bolts, hole patterns, and embed plates. Enter nominal and actual X/Y coordinates for instant Pass/Fail results.

• GD&T
• Quality Control
• Precision

Calculate sheet metal Bend Allowance, Bend Deduction, Outside Setback, and flat pattern length. Material presets for steel, aluminium, stainless, and copper.

• Sheet Metal
• Fabrication
• Press Brake

Calculate inner bore volume (litres / gallons), pipe material volume, and outer envelope volume for any circular pipe.

• Piping
• Volume
• Hydraulics

Calculate board feet (BF) from lumber thickness, width, length, and quantity — with volume conversions.

• Lumber
• Volume
• BF

Estimate vinyl siding order area, squares, and panel count from wall dimensions, openings, gables, waste allowance, and panel exposure.

• Squares
• Panels
• Waste

Estimate bricks for a wall using dimensions, openings, joint thickness, and waste allowance.

• Walls
• Mortar
• Count

Estimate plywood/OSB sheets from surface area, openings, sheet size (4×8 etc.), and waste allowance.

• Sheathing
• Sheets
• Waste

Estimate broadloom carpet (roll goods) by roll width or carpet tiles by tile size, including waste allowance.

• Broadloom
• Tiles
• Square yards

Calculate the exact volume of concrete needed for slabs, footings, and columns in cubic metres, feet, or yards.

• Slabs
• Footings
• Volume

Calculate concrete volume for round piers using Sonotube diameter, pour height, quantity, and waste allowance.

• Piers
• Decks
• Volume

Calculate epoxy volume for floor coatings, self-leveling floors, and anchor bolt installations. Get Part A and Part B quantities.

• Coatings
• Flooring
• Anchoring

Calculate the number of pavers, gravel base, and bedding sand required for patios, walkways, and driveways.

• Landscaping
• Hardscaping
• Count

Calculate floor joist count, rim joists, solid blocking, linear footage, board feet, and stock pieces for any room size and joist spacing.

• Framing
• Lumber
• Structural

Estimate roof area from footprint and pitch, then calculate bundles (shingles) or sheets (by coverage).

• Shingles
• Sheets
• Area

Estimate birdsmouth notch depth and height above plate (HAP) from pitch, rafter depth, and seat cut length.

• Rafters
• Pitch
• HAP

Calculate common rafter length from span/run, pitch, ridge allowance, overhang, and waste allowance.

• Rafters
• Pitch
• Length

Calculate rafter lengths, purlin height, total rise, roof surface area, and shingle quantities for gambrel (barn) roofs with upper and lower pitch panels.

• Barn roof
• Rafters
• Shingles

Calculate member lengths, ridge height, and board-foot lumber for King-Post, Queen-Post, Fink (W-truss), Howe, and Pratt roof trusses.

• King-Post
• Fink
• Board feet

Calculate crushed stone volume, weight (tons / tonnes), bags, and truck loads for driveways, paths, drainage, and landscaping. Six stone types.

• Site Work
• Volume
• Driveway

Calculate tonnes or cubic metres of gravel, sand, or aggregate for foundations and paths.

• Gravel
• Sand
• Tonnes

Estimate asphalt tonnage from area and compacted thickness using a density-based conversion.

• Tonnage
• Driveways
• Thickness

Estimate asphalt millings (RAP) volume and weight from area and compacted thickness, with compaction and optional cost.

• RAP
• Driveways
• Cost

Estimate riprap volume and tonnage from area, layer thickness, waste allowance, and bulk density.

• Erosion control
• Tonnage
• Volume

Estimate floor tiles to order from room size, openings, waste allowance, grout joint, and optional per-box coverage.

• Tiles
• Grout
• Boxes

Estimate drain rock, excavation, fabric area, pipe length, and slope drop for a French drain trench.

• Drain rock
• Fabric
• Slope

Calculate pond water volume, liner size, excavation volume, and minimum pump flow rate for rectangular, circular, and oval ponds.

• Landscaping
• Volume
• Liner

Estimate tiles or planks using room area, waste allowance, and optional box coverage.

• Tiles
• Planks
• Area

Estimate paint for walls and ceilings using coats, coverage, and waste allowance.

• Walls
• Litres
• Coverage

Estimate river rock volume, weight, coverage area, and optional cost in USD from area, depth, and density.

• Landscaping
• Coverage
• Cost

Estimate sod needed from area and waste allowance, optionally estimate rolls/pallets by coverage per unit, and calculate cost in USD.

• Lawn
• Area
• Cost

Estimate septic tank size by bedrooms or by daily flow, with optional disposal adjustment and standard-size rounding.

• Septic
• Sizing
• Gallons